武汉莫诺***「螺耐斯」

杆柱脱落Rod shedding杆柱脱落也是螺杆泵常发生的一种故障现象，表现为运行电流很低，井口也无产液，正反循环油套不连通，通过对扣或下入抽油杆打捞工具就可以进行处理来恢复生产。抽油杆脱落也有两种情况，一是脱扣，一是掳扣。造成脱扣的原因是停机后抽油杆柱扭转变形余能释放引起杆柱反转，可以采取在地面和抽油杆柱上安装防倒装置进行防止。造成杆柱掳扣的原因有三个：一个是稠油井在长时间关井后再启泵时，启动扭矩特别大，把螺纹损坏了；一个是油特别稠，螺杆泵长期在高扭矩下工作而把螺纹损坏；再有一个原因是定子部分脱胶，转子转不动造成的。



Ｄ、限位器D, limiting device限位器为一个底部带限位板和流通通道的短节，接在定子的尾部，其作用是施工作业时给转子限位以防止下入过头而失去作用和杆柱脱落时防止杆柱掉入井底。The limiting device is a short section with bottom limit plate and distribution channel, which is connected to the tail of the stator. Its function is to limit the rotor to the rotor during ctruction1, so as to prevent it from falling into the overhead and lose its function and prevent the rod from falling into the bottom when the rod string falls off.



Ｆ、抽油杆F, sucker rod所使用的抽油杆是常用的普通抽油杆、空心抽油杆和连续抽油杆，可根据油井确定。The sucker rod used is commonly used as a common 1sucker rod, hollow sucker rod and continuous sucker rod, which can be determined according to the oil well.Ｇ、定子扶正器G, stator centralizer定子扶正器为有一定弹性的笼形装罩，每一对由两半构成，中间大、两端小。作用是使定子居中和减小定子的摆动。The stator centralizer is a cage shaped cover with a certain elasticity. Each pair is made up of two halves, large in the middle and small at both ends. The function is to make the stator middle and reduce the stator wobble.Ｈ、锚定装置H, anchoring device对于没有封隔器的井和泵挂深度浅的井，用于固定定子、消除摆动和防止定子脱扣。采用普通的锚定装置即可。For wells without packers and shallow wells with deep pumps, it is used to fix the stator, eliminate the swinging and prevent the tripping of the stator. A common anchoring device can be used.



 单螺杆泵类别：    泵从大类分为两种：容积泵和流量泵。    容积泵：通过泵的传动部件形成的空腔转运流体，传动部件的转动移出流体分为往复式和旋转式两大类    流量泵：带给流体动能，流体转运和循环；不允许干运行，液面以下运转单螺杆泵特点：    1、在低转速工况下压力稳定    2、低必须气蚀余量    3、可输送含大颗粒的介质    4、可输送含磨蚀性的介质    5、压力可至48B    6、流量稳定、可用于计量加药    7、流量对介质的粘度高低影响不大    8、只有一处轴封、便于检修