湖北莫诺转子优惠报价「螺耐斯」

杆柱脱落Rod shedding杆柱脱落也是螺杆泵常发生的一种故障现象，表现为运行电流很低，井口也无产液，正反循环油套不连通，通过对扣或下入抽油杆打捞工具就可以进行处理来恢复生产。抽油杆脱落也有两种情况，一是脱扣，一是掳扣。造成脱扣的原因是停机后抽油杆柱扭转变形余能释放引起杆柱反转，可以采取在地面和抽油杆柱上安装防倒装置进行防止。造成杆柱掳扣的原因有三个：一个是稠油井在长时间关井后再启泵时，启动扭矩特别大，把螺纹损坏了；一个是油特别稠，螺杆泵长期在高扭矩下工作而把螺纹损坏；再有一个原因是定子部分脱胶，转子转不动造成的。



定转子过早磨损Premature wear of fixed rotor定转子过早磨损主要是由于定转子的间隙过小引起的。The premature wear of the fixed rotor is mainly caused by the small gap between the fixed rotor and the rotor.油管与抽油杆柱磨损Oil pipe and rod string wear油管与抽油杆柱磨损的原因一是因为井斜抽油杆贴在油管壁上引起的，可以通过加抽油杆扶正器使抽油杆柱居中来减轻或消除，另一个原因是定转子不同心及转子的偏心运动造成的，在定子以上加一节内径较大的回转筒即可避免。Tubing and sucker rod wear reason is because the deviation of sucker rod attached to the tubing wall caused by heating, pumping rod centralizer make the rod center to reduce or eliminate, another reason is caused by the eccentric motion of the rotor and the rotor are not concentric, avoid a day the diameter of rotary cylinder in the stator can be larger than.



Ｄ、限位器D, limiting device限位器为一个底部带限位板和流通通道的短节，接在定子的尾部，其作用是施工作业时给转子限位以防止下入过头而失去作用和杆柱脱落时防止杆柱掉入井底。The limiting device is a short section with bottom limit plate and distribution channel, which is connected to the tail of the stator. Its function is to limit the rotor to the rotor during ctruction1, so as to prevent it from falling into the overhead and lose its function and prevent the rod from falling into the bottom when the rod string falls off.



211G型单螺杆泵可无脉动地工作 　　G型单螺杆泵工作时,通过螺杆转子与泵套的孔壁间形成的一个个密封腔,平稳地从低压区运送到高压区,在整个运送过程中,介质作纯轴向运动,可完全做到无脉动地运送介质。这一点与齿轮泵不同。齿轮泵工作时,在齿轮的转动下,介质作轴向与径向及其复合方向的运动,产生明显的搅拌现象。其输出压力的表现形式:G型单螺杆泵的输出压力比较稳定,齿轮泵则出口压力会有波动。这一点在输送高粘度的介质(如重油等)时比较突出。