湖北莫诺螺杆泵配件推荐厂家,螺耐斯环保

定转子过早磨损Premature wear of fixed rotor定转子过早磨损主要是由于定转子的间隙过小引起的。The premature wear of the fixed rotor is mainly caused by the small gap between the fixed rotor and the rotor.油管与抽油杆柱磨损Oil pipe and rod string wear油管与抽油杆柱磨损的原因一是因为井斜抽油杆贴在油管壁上引起的，可以通过加抽油杆扶正器使抽油杆柱居中来减轻或消除，另一个原因是定转子不同心及转子的偏心运动造成的，在定子以上加一节内径较大的回转筒即可避免。Tubing and sucker rod wear reason is because the deviation of sucker rod attached to the tubing wall caused by heating, pumping rod centralizer make the rod center to reduce or eliminate, another reason is caused by the eccentric motion of the rotor and the rotor are not concentric, avoid a day the diameter of rotary cylinder in the stator can be larger than.


Ｆ、抽油杆F, sucker rod所使用的抽油杆是常用的普通抽油杆、空心抽油杆和连续抽油杆，可根据油井确定。The sucker rod used is commonly used as a common 1sucker rod, hollow sucker rod and continuous sucker rod, which can be determined according to the oil well.Ｇ、定子扶正器G, stator centralizer定子扶正器为有一定弹性的笼形装罩，每一对由两半构成，中间大、两端小。作用是使定子居中和减小定子的摆动。The stator centralizer is a cage shaped cover with a certain elasticity. Each pair is made up of two halves, large in the middle and small at both ends. The function is to make the stator middle and reduce the stator wobble.Ｈ、锚定装置H, anchoring device对于没有封隔器的井和泵挂深度浅的井，用于固定定子、消除摆动和防止定子脱扣。采用普通的锚定装置即可。For wells without packers and shallow wells with deep pumps, it is used to fix the stator, eliminate the swinging and prevent the tripping of the stator. A common anchoring device can be used.


211G型单螺杆泵可无脉动地工作 　　G型单螺杆泵工作时,通过螺杆转子与泵套的孔壁间形成的一个个密封腔,平稳地从低压区运送到高压区,在整个运送过程中,介质作纯轴向运动,可完全做到无脉动地运送介质。这一点与齿轮泵不同。齿轮泵工作时,在齿轮的转动下,介质作轴向与径向及其复合方向的运动,产生明显的搅拌现象。其输出压力的表现形式:G型单螺杆泵的输出压力比较稳定,齿轮泵则出口压力会有波动。这一点在输送高粘度的介质(如重油等)时比较突出。


现将在现场采用同规格的G型单螺杆泵及齿轮泵在完全相同工况条件下并在输送出口压力为1 MPa时进行了简单的对比,测量了这样两组数据:当输送重油粘度约为75×102-6m2/ s时,齿轮泵出口压力表的指针跳动幅度为±0.16,三螺杆泵出口压力表的指针跳动幅度为±0.05,双螺杆泵出口压力表的指针跳动的幅度为±0.04 ;而当输送重油粘度约为150×102-6m2/ s时,齿轮泵出口压力表的指针跳动幅度为±0.22,三螺杆泵出口压力表的指针跳动的幅度为±0.06,双G型单螺杆泵出口压力表的指针跳动的幅度为±0.04。这说明,G型单螺杆泵在重油的输送和喷燃过程中,介质的输送压力很稳定。并且随着介质粘度的加大,G型单螺杆泵(尤其是双螺杆泵)的无脉动特点相比之下更为明显。